Crucial Handles Made Cheaper. Hardware aluminum handles are very important in everyone’s daily lives. They can be seen in doors, cabinets, and drawers. These hardware handles are used to put pressure by pulling, pushing, or carrying things so they should …
Continue reading
Category Archives: Die Casting Alloys
The Basics of Die Casting Alloys 2021
The Basics of Die Casting Alloys. Die-casting is very comparable to permanent mold casting, only that the metal which is pushed into the mold experiences higher pressures which total to 10-210Mpa (1,450-30,500) psi. Because of this, the exterior of the die-cast is very fine; the dimensions are also much more precise at 0.2% of casting dimension.
Die-casting may be done in two different ways, either utilizing a cold chamber method or by employing a hot chamber procedure. Both vary in the time exposure of the melt which certain metals need either more or less. Cold chamber procedures are typically utilized for aluminum and copper, also counting its fellow die casting alloys. The metal is located in the cold chamber for each shot and requires less time exposure of the melt. Hot chamber methods normally are utilized for metals that have low melting points and high fluidity. This includes zinc, tin and lead. The die cavity is located permanently in the melted metal. The inlet port of the pressurizing cylinder is exposed as the plunger moves to its opening position. This permits a different charge of melted metal to fill the cavity.
Aluminum, Zinc and Copper are the die casting alloys that are chiefly utilized in die-casting for a variety of reasons. Die-castings are restricted from 20kg to a maximum that is reliant on the metal. Large castings typically have superior porosity problems because of the trapped air and the premature hardening of the die-cast cavity. In essence, many things must considered when performing die-casts in order to make certain the excellence of the metals. Die casting alloys guarantee excellent quality and a great finish.
Kinetic Die Casting is located in North Hollywood,California. KDC specializes in manufacturing zinc and aluminum alloy casting parts. If you would like a quote, please visit our website:Kinetic Die Casting Company
The Basics of Die Casting Alloys
Die Casting Alloys
Die Casting Alloys
Die Casting Metals and Technical Terms
Die Casting Technical Information
Die Casting Aluminum Parts
Die Casting Zinc Parts
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605 USA
E-mail sales@kineticdc.com Toll Free: (800) 524-8083 Local: (818) 982-9200
Die Casting Parts Prices
Aluminum Alloy in 2021
Aluminum die casting alloy is lightweight and possesses the stability to come up with thin walls and different shapes. This metal can resist corrosion and other mechanical properties. Moreover, it has excellent electrical and high thermal conductivity. Above all, aluminum die castings can withstand high pressure and temperature. That’s why aluminum is the most common metal used in die casting.
Die casting started in 1800. A patent was granted for the first machine for die casting printing in the year 1849. The die casting process was only limited to printer’s type but development of other shapes have been developed many years after. Aluminum die casting was introduced in 1914 and it gained popularity. Furthermore, die casting this kind of metal is still used today.
The Aluminum Die Casting Process of exerting high pressure to molten aluminum into molten cavities. These molds are called dies. They can be designed to come up with accurate and complex shapes. Parts can be defined to produce textured or smooth surfaces. Die cast products range from aircraft and automobile parts, toys, and even household utensils.
Die casting is an economical and efficient process that offers a wide range of components and shapes. Parts that have been made through die casting have long service life. Moreover, it provides high-speed production and requires less or no machining at all. Furthermore, you can make thousands of similar castings before you use additional tools.
Aluminum die casting company generates parts that are dimensionally stable and strong, while maintaining close tolerances. Also, parts that have been die casted are stronger compared to plastic injection moldings.
Kinetic Die Casting manufactures aluminum and zinc die casting parts. Samples of KDC’s work include die cast speaker parts, aluminum tile plates, and other die cast metal parts. If you would like to have a quote please visit our website: Kinetic Die Casting Company
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605, United States of America
E-mail sales@kineticdc.com USA Toll Free: (800) 524-8083 Local: (818) 982-9200
To get prices for Die Casting Tooling Molds or Parts: RFQ Die Casting Part Prices
Kinetic Die Casting Company makes:
FAQ Die Casting Questions and Answers
Kinetic Die Casting Capabilities
Kinetic Die Casting Jobs
Roof Tile Molds Company
The Different Alloys Used in Die Casting Manufacturing in 2020
Die Casting Alloys – The Different Alloys Used in Die Casting Manufacturing. Kinetic Die Casting Company uses different types of metal die casting alloys depending on the needs of our customers.
-
The Die Casting Alloys we use are:
- A360 aluminum die casting alloy
- A380 aluminum die casting alloy
- A383 aluminum die casting alloy
- A413 aluminum die casting alloy
- ZA27 die casting alloy
- #3 zinc die casting alloy
- #5 zinc die casting alloy
A380 is the die casting alloy we use the most. About 80% of our parts are produced in A380. A380 is the least expensive aluminum alloy. It is very versatile for a very nice finish on a die casting part.
A360 aluminum die casting alloy is used when corrosion resistance is required. It is used by many manufacturers whose parts are exposed to salt spray or other corrosive environments.
A413 die casting alloy is another alloy we use to produce a lot of parts. This alloy is used in a lot of thermal conductance applications (heat sinks). It has a very nice surface finish and can be used to cast thinner walls. It has better corrosion resistance than A380.
A383 alloy is less expensive than A413 and also is used when the die casting part wall thicknesses are thinner than normal.
ZA27 die casting alloy is used when greater die casting part strength is needed. This die casting alloy is a marriage between aluminum and zinc.
#3 and #5 zinc die casting alloys are the most common alloys used for zinc die casting. Many of the products that were produced in zinc are now made in aluminum or plastic. Zinc makes up less than 10% of the die casting parts made in America today.
Contact Kinetic Die Casting Company for your die casting part needs. (818-982-9200)
Kinetic Die Casting manufactures zinc and aluminium die casting. If you would like a quote, please visit our website:Die Casting quote
Die Casting Alloys
Die Casting Alloys
Die Casting Metals and Technical Terms
Die Casting Technical Information
Die Casting Aluminum Parts
Die Casting Zinc Parts
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605 USA
E-mail sales@kineticdc.com Toll Free: (800) 524-8083 Local: (818) 982-9200
Die Casting Parts Prices
Are Aluminum Die Casting Parts stronger and cheaper than Steel in 2020?
Are aluminum die casting parts stronger and cheaper than steel?
How can an aluminum die cast part be stronger than a steel weldament? Kinetic Die Casting, Inc. makes an aluminum die casting Boomerang cam lever part for a lift manufacturer that once was a two pound steel welded unit. This unit consisted of two steel plates, 1/8″ thick, with holes drilled, tapped, and welded to steel spacers with a bushing at each end, then painted. Occasionally, these units would fail in the field. Manufacturing costs ran about $7.00 per part in production quantities of 1,000 each week. Another difficulty is that it took three to four weeks to make the first steel part and only a few 100 could be produced a week. This hindered increased sales.
Kinetic Die Casting now produces these parts in aluminum die casting that weigh only 3/4 pounds; the steel unit weighed over two pounds. The aluminum die casting parts are stronger (3x greater axial load) and more reliable. There is no need for paint on the aluminum die casting parts. The Kinetic Die Casting part price of each die casting unit is less than $3.00.
Kinetic Die Casting can help you develop an aluminum die casting that will reduce weight, increase strength, and cost you less money.
Advantages of the Aluminum Die Cast Part over the Steel Weldament:
- 3x greater axial load strength.
- Fewer part failures in the field and fewer returns to the OEM.
- Part weight is 2.5x less in aluminum saving money in shipping cost.
- Production quantities (1,000’s) within a few days instead of weeks as before.
- Production rate is faster as an aluminum die cast part.
- Raw part manufacturing cost is 2.3x less as an aluminum die cast part.
- Finishing cost is less as an aluminum die cast part.
- Better looking parts as a die cast part.
- More details here https://www.kineticdiecasting.com/steel.html
Kinetic Die Casting manufactures die cast parts for their customers. If you would like to know more about what is die casting or if you would like a quote, please visit our website:Kinetic Die Casting Company
Steel Parts or Plastic Parts or Die Casting Parts
Metal or Plastic Parts
Custom Metal Part Castings
Die Casting Parts Porosity
Die Casting Pats Photos
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605 USA
E-mail sales@kineticdc.com Toll Free: (800) 524-8083 Local: (818) 982-9200 Fax: (818) 982-0877
Die Casting Part Prices
Die Casting Zinc Alloys Quick Info in 2020
Die Casting Zinc Alloys Quick Info. Die casting zinc alloys is a common practice amid metalworkers due to the fact that zinc alloys have several uses. 
Zinc has decent properties: it doesn’t rust, it is light yet durable, it’s non-corrosive, it is multipurpose, and it is easily flexible. Zinc may be shared with other materials such as aluminum, copper, magnesium, and tin, to state a couple. Their arrangements accomplish definite effects dependent on the quantities and types of materials used and the die casting process.
To die cast zinc metals, zinc and other alloys are joined via chemical developments and heated under high temperatures to become fluid. When they attain this molten state, they are forced to pour into die casts where they take on the mold’s design. Upon cooling, the metals keep the shape and stay that way until they are heated again. Here are some ways that zinc alloys are used:
• To coat metal items and guard them from corrosion
• To protect electrical pieces
• To form unbending metal components
• To substitute costly metalworking supplies
• To help as a lightweight alternative for some metal materials
Die casting zinc alloys are worthwhile in generating a lot of things, such as fixtures, vehicles, equipment, tools, weaponry, etc. It is chosen to other means of creating zinc alloys because die casts make it easier for the alloys to be shaped exactly in a little time. Also, it doesn’t take much exertion to pour molten alloy into the cast and let them set resolutely as matched to forging and hammering. Because of its various benefits, die casting zinc alloys has continued to be a extensive practice in metallurgy.
This is the blog on the Kinetic Die Casting Company web site. We make several types of Aluminum Handle Parts. Look at this website page for more details: www.kineticdiecasting.com/handle.html. Contact Kinetic Die Casting Company at 818-982-9200 or email us at sales@kineticdc.com. Use this webpage to request “die casting part prices” www.kineticdiecasting.com/replyform.html
Do you need fast delivery for military die casting parts? Kineticdc shipped military parts that were die castings with impregnation, chemical filmed and machined in less than two weeks from receipt of a purchase order. Know someone that wants to buy die cast parts and can use our die casting services?
Call us and let us know 818-982-9200.
Kinetic Die Casting Company 6918 Beck Avenue North Hollywood California 91605
www.kineticdc.com #diecasting #kineticdc #manufacturing @kineticdc #zinc
Kineticdc makes:
Automotive Die Casting Parts
Light Fixture Die Casting Parts
Consumer Products Aluminum Parts
Aerospace Die Casting Parts
Military Die Casting Parts
Die Casting Alloys
Die Casting Alloys
Die Casting Metals and Technical Terms
Die Casting Technical Information
Die Casting Aluminum Parts
Die Casting Zinc Parts
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605 USA
E-mail sales@kineticdc.com Toll Free: (800) 524-8083 Local: (818) 982-9200 Fax: (818) 982-0877
Die Casting Parts Prices
