North American Die Casters Association 30 (NADCA) Chapter 30 members and supporters – Register to join us for the AFS NADCA 2025 Vendors Night on Thursday, March 13th! Last year we had record attendance and this year promises to be …
Continue reading
Category Archives: Die Casting Company
Aluminum Die Casting Radiator: Aluminum Die Casted Car Parts: 2020
Aluminum Car Part
Your car radiator is the primary cooling mechanism for your engine. Radiators are a simple and elegant solution to the need for engine cooling. Car radiator parts are mostly made of aluminum. Light and strong, aluminum is great for making car radiators. It is the material of choice for most of today’s radiators. Light and intelligently designed, aluminum radiators are standard on many of today’s new cars and trucks. Aluminum Car Parts
A small leak on your car Radiator can be indicating a larger problem. A cooling system that runs low too often is less efficient and you can damage your cooling system by letting the coolant level get too low. Too little coolant flow can be bad, but at normal and high operating temperatures, the rate at which coolant moves through the radiator does not change the amount of heat that is dissipated by the cooling cores. The amount of cooling will not be reduced even when the mean temperature of the coolant rises and flows faster.
Many cheap coolants do not have the corrosion protection, PH balancing, or sediment prevention that the top-quality coolants do. These low quality coolants do not have the same additives of name brand coolants. To help your engine stay cooler, rev up your engine slightly when you are overheating in traffic to help push more air across the cooling cores and more coolant through the engine.
All water-cooled car radiator parts have an automatically controlled electric fan on the radiator. The way the system is supposed to work is that, after the engine is started, the thermostat on the engine stays closed until the coolant temperature at the ENGINE reaches 87C (189F) degrees. It is the responsibility of the Radiator to keep the coolant temperature from running too high. However, if the temperature is too high it is not necessarily the radiator.
A poor radiator cap will not last as long or stay properly calibrated, and either open at too low or two high a pressure. Make sure your radiator cap is the proper one for your cooling system. Higher pressure means a higher boiling point, which means more efficient cooling. A new radiator cap is usually all that is required for this (but don’t over pressurize your radiator cores and wreck the whole system).
Most Car Radiators’ cooling system failures arise from poor radiator maintenance. Many radiator problems can be prevented with regular maintenance and periodic professional inspections of you car radiator and cooling system. The most common radiator problems are: leaky fittings or seams, fin deterioration and bond failure, electrolysis, cracked tank, and fan damage.
Kinetic Die Casting manufactures aluminum and zinc die casting parts. Samples of KDC’s work include Ricon V2-AC 090 Cam Arms, aluminum tile plates, and other die cast metal parts. If you would like to have a quote please visit our website: Kinetic Die Casting Company
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605, United States of America
E-mail sales@kineticdc.com USA Toll Free: (800) 524-8083 Local: (818) 982-9200 Fax: (818) 982-0877
To get prices for Die Casting Tooling Molds or Parts: RFQ Die Casting Part Prices
Kinetic Die Casting Company makes:
Light Fixture Die Casting Parts
Photos Die Casting Parts
Aerospace Die Casting Parts
Roofing Tile Molds Blog
Posted in Aluminum Die Casting, Auto Parts, Die Casting Company, Die Casting Parts, Diecasting Process
Tagged #diecasting, #kineticdc, aluminum, Aluminum Auto Parts, Aluminum Die Casting, Aluminum Die Casting Company, aluminum parts, auto parts, car parts, Diecasting Process, Kinetic Die Casting Company
Leave a comment
CEP Cast Engineering Products Closing
Today, I received the sad news that another local Southern California die casting company competitor is closing. CEP (Cast Engineered Products), is closing their doors. CAST and ENGINEERED PRODUCTS was located at 1746 West 135th Street, Gardena, CA 90249-2508 Telephone Voice:310.323.8460 Sales@cepUSA.com. I have known the owner, Ismail Cuhadar over 30 years. Ismail had over 35 years of experience in the die casting and metals industries. Ismail is a graduate of The University of Southern California and holds Master of Science and Professional Engineer degrees in Mechanical and Design Engineering. I met him when he worked at El Monte Tool and Die Casting Company. Ismail then went to Modern Die Casting Company / Sunny Die Casting Company before he started CEP.
In 1994, Ismail founded CEP in Downey, CA out of Modern/Sunny. Then in 2001, he moved its operations to the larger facility in Gardena, CA to manufacture aluminum and zinc die castings, bronze and copper-nickel porous powder metal parts and other engineered products. I always enjoyed spending time with Ismail, I wish him safety, health and happiness.
If your company is in search of a replacement die casting parts supplier, you can contact us at Kinetic Die Casting Company:
Kinetic Die Casting Company, Inc.
( https://www.kineticdiecasting.com )
1-818-982-9200
E-mail sales@kineticdc.com
6918 Beck Avenue
North Hollywood, CA 91605
Permalink: https://www.kineticdiecasting.com/kdc/cep-cast-engineering-products-closing/
Posted in Blogger, Business, Customers, Die Casting Company, Die Casting Parts, newsletter, Supplier
Tagged #competitor, #diecasting, Business, Die Casting Company
1 Comment
Aluminum Aircraft Parts Die Casting 2020
AIRCRAFT PARTS ALUMINUM DIE CASTING
Aircraft Die Cast Part1
If you happen to look above and you see a fast fighter plane equipped with modern design and armed with missiles, you’ll surely say that it’s from the United States. The United States is the leader in aircraft manufacturing. The country is supported by an array of fighter planes for national security and defense. But how did they build aircrafts? Well, those aluminum airplane parts are made because of die casting.
What is a die casting company anyway? Die casting is the process of forcing molten metal under high pressure into mold cavities. Most are made from copper, zinc, aluminum, lead, magnesium, tin and lead based alloys it is used for applications where small parts need to be given a good detail or a perfect surface quality. Furthermore, in aircraft die casting magnesium and aluminum are the commonly used metals because they are lightweight and can operate in different conditions.
Magnesium alloy castings showed corrosion resistant performance. Other than that, magnesium alloys are light weight, low density and it can operate at high temperature. There are several magnesium alloys that can be found in an aircraft such as the RZ5 alloy in helicopter transmission casings and WE43 alloy for the castings of the main rotor gearbox.
Aluminum on the other hand remained to be the most popular alloy used on aircrafts. The parts of aircraft that uses aluminum alloy are door handle ducts, boxes, brackets, quadrants, clips, doublers, wave guides, wing and the body.
Aircraft parts die casting have gone along way. Although aluminum and magnesium are the popular metals used in aircrafts, others are still looking for other options like titanium.
Kinetic Die Casting manufactures aluminum and zinc die casting parts. Samples of KDC’s work include die cast speaker parts, aluminum tile plates, and other die cast metal parts. If you would like to have a quote please visit our website: Kinetic Die Casting Company
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605, United States of America
E-mail sales@kineticdc.com USA Toll Free: (800) 524-8083 Local: (818) 982-9200 Fax: (818) 982-0877
To get prices for Die Casting Tooling Molds or Parts: RFQ Die Casting Part Prices
Kinetic Die Casting Company makes:
What Are Die Casting Parts?
Die Casting Aluminum Heat Sinks
Aluminum Boxes Diecastings
Kinetic Die Casting SEO
Posted in Aircraft Parts, Aluminum Die Casting, Die Casting Company, Die Casting Parts, Diecasting Process, Kinetic Die Casting Company
Tagged #diecasting, #kineticdc, Aircraft Parts, Airplane Castings, Airplane Parts, aluminum, Aluminum Die Casting, die casting, Die Casting Parts, Die Casting Process, Die Castings, Diecasting Process, Kinetic Die Casting Company
Leave a comment
MTD Die Casting Company Closed
PLANT CLOSED – MTD Products Inc. 2555 BRANDENBURG ROAD LEITCHFIELD, KENTUCKY 42754 Auction for equipment on FRIDAY, JUNE 19TH at 10:00 AM eastern time (EST) WEBCAST ONLY, NO ONSITE BIDDING. Featuring: DIE CASTING MACHINES – (8) HPM and IDRA Die Casters up to 1,000-Tons • (7) METAL MECHANICS 50-Ton & 35-Ton Trim Presses, New as of 2009 • Ladlers • FANUC Loading Robots • Melting Furnaces.
MODERN TRANSMISSION DEVELOPMENT COMPANY (MTD) Die Casting & Plastic Injection Molding Facility Auction Details (WEBCAST ONLY)
Link: https://www.myronbowling.com/auctions/modern-transmission-development-mtd-webcast-only-1181c50.html?LayoutID=23
Here is a video posted by Myron Bowling the auction company of the die casting robotic arm taking out a die casting part from the die casting machine:
The facility employed approximately 295 people and manufactured component and aftermarket parts used to supply the company’s assembly facilities. “MTD is grateful for the hard work and dedication of these employees and the continued support of the Leitchfield community,” said Craig Dukes, senior vice president of Human Resources. “We recognize the significant impact this closure will have on employees and their families and will be providing separation support including severance benefits, outplacement services and preferential hiring opportunities at MTD’s other US facilities.”
MTD made this decision after careful and ongoing evaluation of its manufacturing footprint in relation to future strategic needs, according to Eric Creech, MTD’s Communications and Marketing Manager. The move will improve overall efficiency and better position MTD to deliver competitive products in a rapidly evolving outdoor power equipment industry.
MTD, located at 2555 Brandenburg Road, remains committed to U.S. manufacturing and has increased employment at its other U.S. manufacturing facilities over the last several years, the company said. The move also allows the company to focus on better leveraging advanced manufacturing capabilities in its other U.S. facilities.
Permalink: https://www.kineticdiecasting.com/kdc/mtd-die-casting-company-closed/
For Large Industries: The Process of High Pressure Die Casting
For Large Scale Industries: The Process of High Pressure Die Casting. The process of high pressure die casting is popular among large scale production lines. It is considered as one of the most cost effective and fastest metal working process, when compared to forging, sand casting and other types of machining. Traditional die casting is also called high pressure die casting because the molten metal is forced into the mold cavity by using high pressure.
The mold cavity is formed by two halves. They are the cover die and the ejector die. The section where the two halves meet is called the parting line. During casting, molten metal is injected between the dies. The metal is allowed to flow through an opening in the cover die half. High pressure, between 10 to 175 mPa, is maintained until the molten metal solidifies. This process of high pressure die casting ensures uniform solidification of the final product. Hence, it produces uniform work pieces with high yield strength. There are two types of the method: cold chamber and hot chamber casting. The choice depends on the melting point of the metal. For example, zinc and aluminum alloys can only be processed in cold-chamber environments.
The process of high pressure die casting has many applications, ranging from the toy industry to automotive and computers. The technique also minimizes, if not totally eliminates, post-machining like sanding or grinding. Therefore, there are less post-production costs. However, this technique is only recommended for large scale businesses. The initial cost of construction of dies, due to painstaking details and strength, is relatively higher than other machining processes.
To get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at E-mail sales@kineticdc.com for a fast response on a price quote.
Kinetic Die Casting manufactures aluminum die castings creating aluminum die casting boxes, aluminum handle hardware, and aerospace die casting. If you would like to get a quote, please visit our website: Kinetic Die Casting Company
Kinetic Die Casting manufactures products like heatsink die casting, aluminum housings, and lighting fixtures. If you would like more information, please visit our website:Kinetic Die Casting Company
Die Casting Process
What is Die Casting?
Aluminum Die Casting Prices
Why Should You Use Die Castings?
Kinetic Die Casting Company
Kinetic Die Casting Company 6918 Beck Avenue, North Hollywood, California 91605 USA
E-mail sales@kineticdc.com Toll Free: (800) 524-8083 Local: (818) 982-9200 Fax: (818) 982-0877
Die Casting Parts Prices
