Tag Archives: Aircraft Parts

Boeing — Not Taxpayers — Will Pay for Cost

Tony Capaccio of Bloomberg Business News reported last week that Boeing may end up spending $300 million more than is budgeted under its contract to develop a new Air Force aerial-refueling tanker.

Bad news for taxpayers, right?

Wrong — because the company will have to eat every cent of expenses above the ceiling on the development contract, which means if there actually is an “overrun,” taxpayers will be getting extra value at Boeing’s expense.

The story could be bad news for Boeing shareholders, but something tells me when the contract is completed Boeing will come in right at the ceiling.

Of course, that still could mean a zero rate of return, but the development contract leads to production of 179 planes, where the big aerospace company is likely to do just fine.

Thompson: Obama’s new acquisition practices “reward honesty and realism.”
What some observers don’t seem to get about the Bloomberg story is that the Obama administration really has tightened up on contracting practices, so if companies don’t stay within budgets, they lose money.

That’s a powerful incentive not to run up costs, and helps explain why the administration pushed for an early transition from cost-plus contracts to fixed-price arrangements on the F-35 fighter too.

In both cases, contractors will get the best results if they stay within budgets, which is exactly what policymakers were aiming to achieve.

There’s no advantage in bidding low to win and then trying to raise prices, because contract terms are too tight to allow recovery. So the new acquisition practices reward honesty and realism.

Government Got the Best Deal Possible

If you’re still stuck in the old way of thinking, then the fact that Boeing might have to eat some extra expenses suggests the company didn’t have a good handle on costs when it wrote its proposal.

Not so: It bid the price it needed to bid to beat rival Airbus. Both companies knew they would have to price their proposals aggressively to have any chance of winning, and as one senior Boeing executive put it to me, “We left a lot of shekels on the table.”

In other words, Boeing was willing to break even or maybe even lose money in the development phase in order to preserve its 50-year tanker franchise and keep Airbus out of its home market.

Thus, Tony Capaccio’s story doesn’t signal that anything has gone wrong with the tanker program. Quite the opposite — it shows government negotiators got the best deal possible from the winner.

Loren B. Thompson, Ph.D., is chief operating officer of the Arlington, Va.-based nonprofit Lexington Institute and chief executive officer of Source Associates, a for-profit consultancy. Prior to holding his present positions, he was deputy director of the Security Studies Program at Georgetown University and taught graduate-level courses in strategy, technology and media affairs at Georgetown. He also has taught at Harvard University’s Kennedy School of Government.

-Industryweek

Kinetic Die Casting utilizes die casting to manufacture parts like aluminum car parts, airplane parts, lighting parts and much, much more. If you would like to request a quote, please visit our website:Die Casting quote

Posted in Business | Tagged , , , | Leave a comment

Metal Working for Aircrafts: Die Castings Used for Airplane Parts.

Metal Working for Aircrafts: Die Castings Used for Airplane Parts. When it comes to aircraft assembly parts, the most important considerations are safety, strength and reliability. The metal parts will sustain turbulence in the upper atmosphere, and they will experience inertial forces and several stresses. This is why die castings used for airplane parts are in-demand nowadays. Metal parts produced by die casting are characterized by high tensile strength, and resistance to torsional, flexural and tensional stresses.

In die casting, a pre-determined amount of molten metal is injected into a mold cavity. That cavity is formed by the cover die and the ejector die, which contain the shape of the target product. While the metal is cooling and solidifying, intense pressure is applied to compress the dies. Other than just shaping, this is a strength enhancing process. Yield can be expected to reach 69%.

Aluminum and magnesium are popular metals for die castings used for airplane parts. They are very durable, stable and with high melting points. Aluminum in particular is very light, comparable with treated plastics. These metals are used for frames and fixtures for the plane, and for fittings that connect bars and handles. Die casted Mg and Al is also present in the engine and mechanical rods.

Die casting is versatile because it can produce simple and complicated designs alike. Parts-supplying companies can finish hundreds of parts within minutes because the process is efficient for large-scale productions. Die castings used for airplane parts include plain sheets, billets and rods. More detailed castings include engine blocks, turbines and mechanical fixtures.

To get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at sales@kineticdc.com for a fast response on a price quote.




Kinetic Die Casting Company


Kinetic Die Casting manufactures die casting metal parts creating products like roofing tile molds, lighting parts, and military parts. If you would like more information about Kinetic Die Casting, visit our website:Kinetic Die Casting Company

Posted in Aircraft Parts | Tagged , , , , , , , | Leave a comment

New Die Casting Military Parts

New Die Casting Military Parts. New Die Casting Military Parts is important as it produces strong and lighter results. Producing high quality military parts using die cast is vital, because ensuring the safety of the military is essential for the safety of the individual as well. You want to make sure that the group of people who keeps you safe is in good hands with right tools and strong equipment.

For the reason that new die casting military parts are produced as a whole and not assembled consisting of detached separated parts, the result is therefore stronger alloy for the equipment.

Right as this moment, New Die Casting Military Parts are produced for the United States Government respectively for the army, navy, air force, missile defense agency, and many others. Examples of these parts are the Fire suppression system housing for armored vehicles. It is important to make its composition well-built as it allows the military tank passengers and drivers to survive in case the fuel tank is hit. Another example is the missile nose piece. It is important to have this die casted because it needs to withstand a lot of pressure and force. Other examples are the Military Fire sensor housing and Military Pump parts.

To get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at sales@kineticdc.com for a fast response on a price quote.




Kinetic Die Casting Company


Kinetic Die Casting is located in North Hollywood,California. KDC specializes in manufacturing zinc and aluminum alloy casting parts. If you would like a quote, please visit our website:Kinetic Die Casting Company

Posted in Die Casting Parts | Tagged , , | 1 Comment

Examples of Aluminum Aircraft Parts

Examples of Aluminum Aircraft Parts. The United States of America is the world’s leader in the production of aircraft and related methods. Military aircraft shape the stamina for both nationwide defense and protrusion of power. The air transportations are significant to air dominance, strike, early warning, airlift, scouting, sea control, ground attack and command and control. Development in air transportation price and ability therefore present important controlling probability for decreasing defense expenses.

  • The B-52H BUFF aka Big Ugly Fat Fellow
    A sum of seven hundred and forty four B-52s were created with the final, a B-52H, transported in 1962. The H representation is the only one that is still in the Air Force account and are all allocated to Air Combat Command. The very first of 102 B-52H’s was transported to the Strategic Air Command in 1961. The H representation can hold up to twenty air instigated cruise missiles. Plus, it can hold the usual cruise missile that was instigated from the B-52G representations.
  • The F-117A Nighthawk Attack Fighter
  • The very first F-117A was transported in the year 1982, and the final Nighthawk deliverance was in the summer of year 1990. The F-117A manufacture verdict was ready in 1978 with a diploma presented to Lockheed Advanced Development Projects.
  • Contact Kinetic Die Casting Company to get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at sales@kineticdc.com for a fast response on a price quote.

    Kinetic Die Casting manufactures aluminum die castings creating aluminum die casting boxes, aluminum handle hardware, and aerospace die casting. If you would like to get a quote, please visit our website: Kinetic Die Casting Company

    Posted in Aircraft Parts | Tagged , , , , , , , , , | 3 Comments

    Methods for Making Aluminum Aircraft Parts

    Methods for Making Aluminum Aircraft Parts. Aluminum which are used in the making of aircraft parts are usually alloyed with other kinds of metals to make the material stronger. This material is at times called duralumin. Aircraft engineers favour aluminum for its density which is low and because it is light weight.

  • One of the common methods for making aluminum aircraft parts is die-casting. This method is specifically befitted to the manufacturing of huge amounts of relatively diminutive parts. Metal moulds are injected with molten metal under ample pressure. The combination of brisk injection and quick curing under high pressure produces a fine-grain, opaque surface structure, and this leads to superb fatigue and wear properties. But shrinkage and air entrapment could possibly lead to porosity; therefore, a limit of 1.0 mm in machine cuts should be established to avoid exposing the material.
  • Another method for producing aircraft parts with aluminum is permanent mold or gravity die casting. Similar to die casting, this method is suitable for high-volume production. Typically, die castings are relatively smaller than permanent mold castings. Permanent mold castings could reach up to 10 kg at maximum; but castings far larger are sometimes custom made when the costs of the production equipment are respectively justified by the specific quality requirements the casting asks.
  • Kinetic Die Casting Company – To get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at sales@kineticdc.com for a fast response on a price quote.

    Kinetic Die Casting is located in Southern California. KDC specializes in aluminum and zinc die casting tooling. If you would like a quote, please visit our website:Kinetic Die Casting Company

    Posted in Aircraft Parts | Tagged , , | 4 Comments