Tag Archives: Airplane Parts

Die Casting Aerospace Parts

Kinetic Die Casting Company makes several types of Die Casting Aerospace Parts. These aerospace die casting parts are used for many types of purposes. Some of these parts are used on many types of aircraft, such as: airplanes, jet planes or helicopters.

Aircraft manufacturers typically specify aluminum die casting to make the aerospace parts because aluminum is lightweight and inexpensive as well as very strong.

  • Lightweight – Aluminum weighs only .098 pounds each cubic inch of material as compared to zinc which weighs about 2.44 pounds each cubic Inch.
  • Inexpensive – Aluminum is the third most common element on earth, so it is more available than other materials. Aluminum is used in over 80% of all die castings produced in the world.
  • Strong – Aluminum parts can be geometrically designed to be stronger than steel. Look up “aluminum is stronger than steel” on Google to see the results.

These aerospace parts range from: airplane engine piston heads, airplane distributor cap housings, fuel system parts, detention ring parts, cargo loading housings, lighting fixture parts, electronic enclosures, electronic housings, motor housings and various other aluminum die casting parts.

The companies that trust us to purchase their die casting parts from Kinetic Die Casting Company are many.

    Here are a few of the aircraft and aerospace companies that we can name:

  • Robinson Helicopter
  • Ancra International
  • Whittaker Controls
  • AAR Cargo Systems
  • Boeing Aerospace
  • Barry Controls
  • Meggitt Aerospace
  • Parker Hannifin Aerospace Corporation (Parker FSD)
  • Circle Seal Aerospace
  • Kelly Aerospace
  • Curtiss Wright
  • Honeywell
  • United Technologies Aerospace

Low Quantities.

Many of these companies order lower quantities. One of the companies listed here will order less than 50 parts at a time. Many of these companies order 250 parts or less. Kinetic Die casting will accept any purchase order quantity.

Contact Kinetic Die Casting Company when you need any of the following: Low Quantities, Great Quality, Fast Delivery.

Kinetic Die Casting Company
6918 Beck Avenue
North Hollywood, CA 91605

Kinetic Die Casting Company

Posted in Aircraft Parts, newsletter | Tagged , , , , | 6 Comments

Aluminum Aircraft Parts Die Castings

Aircraft or better known as Airplanes are large, very large. They are large because they are designed to carry things, lots of things. Airplanes carry mail, gifts, shipments, food, packages, baggage, and people. Airplanes are the fastest transportation for “things” and people today. Airplanes are fast because they travel through the air. Because airplanes are big and travel through the air, the airplane construction materials need to lightweight and strong. Aluminum is used for most of the airplane components because it is lightweight and strong. The overall airplane part weight is kept down so the airplane will be able to carry more “things”. Therefore, aluminum is used a lot.

Aluminum Aircraft Part Picture
http://www.kineticdiecasting.com/aircraft_part_pictures.html
Aluminum Aircraft Part Pictures

https://www.kineticdiecasting.com/kdcgallery/201.01_1.png

Die casting is the preferred manufacturing process for making Aluminum Aircraft Parts. The reason is because the aluminum die casting process has a lot of advantages over other high volume aircraft part manufacturing processes.

    Aluminum Aircraft Parts Produced as Die Castings:

  1. Die Casting is less expensive because more than 500 or 1,000 parts can be produced each day.
  2. Die Casting hold tolerance typically to +/- 0.002″ after the die casting tool is approved.
  3. Aluminum weighs 1/3 by volume of a similar part in steel.
  4. Aluminum die casting parts are very strong.
  5. Die Castings are produced near “net shape”, reducing additional manufacturing costs.
  6. Die Casting Tooling reliably manufacturers parts repeatably over several thousand parts.
  7. Aluminum die castings do not break down over time as other materials break down.
  8. Aluminum die castings have an aesthetically pleasing surface finish.
  9. Die Casting parts look good after paint or polish.

    Kinetic Die Casting Company makes many types of aircraft parts. We make:

  • Airplane distributor caps
  • Aircraft wheel cove locks
  • Cargo Plane bearing housing parts
  • Airplane piston heads
  • Many others….

Kinetic Die Casting manufactures die casting metal parts creating products like roofing tile molds, lighting parts, and military parts. If you would like more information about Kinetic Die Casting, visit our website:Kinetic Die Casting Company

Posted in Aircraft Parts, newsletter | Tagged , , , , , | 3 Comments

Boeing — Not Taxpayers — Will Pay for Cost

Tony Capaccio of Bloomberg Business News reported last week that Boeing may end up spending $300 million more than is budgeted under its contract to develop a new Air Force aerial-refueling tanker.

Bad news for taxpayers, right?

Wrong — because the company will have to eat every cent of expenses above the ceiling on the development contract, which means if there actually is an “overrun,” taxpayers will be getting extra value at Boeing’s expense.

The story could be bad news for Boeing shareholders, but something tells me when the contract is completed Boeing will come in right at the ceiling.

Of course, that still could mean a zero rate of return, but the development contract leads to production of 179 planes, where the big aerospace company is likely to do just fine.

Thompson: Obama’s new acquisition practices “reward honesty and realism.”
What some observers don’t seem to get about the Bloomberg story is that the Obama administration really has tightened up on contracting practices, so if companies don’t stay within budgets, they lose money.

That’s a powerful incentive not to run up costs, and helps explain why the administration pushed for an early transition from cost-plus contracts to fixed-price arrangements on the F-35 fighter too.

In both cases, contractors will get the best results if they stay within budgets, which is exactly what policymakers were aiming to achieve.

There’s no advantage in bidding low to win and then trying to raise prices, because contract terms are too tight to allow recovery. So the new acquisition practices reward honesty and realism.

Government Got the Best Deal Possible

If you’re still stuck in the old way of thinking, then the fact that Boeing might have to eat some extra expenses suggests the company didn’t have a good handle on costs when it wrote its proposal.

Not so: It bid the price it needed to bid to beat rival Airbus. Both companies knew they would have to price their proposals aggressively to have any chance of winning, and as one senior Boeing executive put it to me, “We left a lot of shekels on the table.”

In other words, Boeing was willing to break even or maybe even lose money in the development phase in order to preserve its 50-year tanker franchise and keep Airbus out of its home market.

Thus, Tony Capaccio’s story doesn’t signal that anything has gone wrong with the tanker program. Quite the opposite — it shows government negotiators got the best deal possible from the winner.

Loren B. Thompson, Ph.D., is chief operating officer of the Arlington, Va.-based nonprofit Lexington Institute and chief executive officer of Source Associates, a for-profit consultancy. Prior to holding his present positions, he was deputy director of the Security Studies Program at Georgetown University and taught graduate-level courses in strategy, technology and media affairs at Georgetown. He also has taught at Harvard University’s Kennedy School of Government.

-Industryweek

Kinetic Die Casting utilizes die casting to manufacture parts like aluminum car parts, airplane parts, lighting parts and much, much more. If you would like to request a quote, please visit our website:Die Casting quote

Posted in Business | Tagged , , , | Leave a comment

Metal Working for Aircrafts: Die Castings Used for Airplane Parts.

Metal Working for Aircrafts: Die Castings Used for Airplane Parts. When it comes to aircraft assembly parts, the most important considerations are safety, strength and reliability. The metal parts will sustain turbulence in the upper atmosphere, and they will experience inertial forces and several stresses. This is why die castings used for airplane parts are in-demand nowadays. Metal parts produced by die casting are characterized by high tensile strength, and resistance to torsional, flexural and tensional stresses.

In die casting, a pre-determined amount of molten metal is injected into a mold cavity. That cavity is formed by the cover die and the ejector die, which contain the shape of the target product. While the metal is cooling and solidifying, intense pressure is applied to compress the dies. Other than just shaping, this is a strength enhancing process. Yield can be expected to reach 69%.

Aluminum and magnesium are popular metals for die castings used for airplane parts. They are very durable, stable and with high melting points. Aluminum in particular is very light, comparable with treated plastics. These metals are used for frames and fixtures for the plane, and for fittings that connect bars and handles. Die casted Mg and Al is also present in the engine and mechanical rods.

Die casting is versatile because it can produce simple and complicated designs alike. Parts-supplying companies can finish hundreds of parts within minutes because the process is efficient for large-scale productions. Die castings used for airplane parts include plain sheets, billets and rods. More detailed castings include engine blocks, turbines and mechanical fixtures.

To get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at sales@kineticdc.com for a fast response on a price quote.




Kinetic Die Casting Company


Kinetic Die Casting manufactures die casting metal parts creating products like roofing tile molds, lighting parts, and military parts. If you would like more information about Kinetic Die Casting, visit our website:Kinetic Die Casting Company

Posted in Aircraft Parts | Tagged , , , , , , , | Leave a comment

Examples of Aluminum Aircraft Parts

Examples of Aluminum Aircraft Parts. The United States of America is the world’s leader in the production of aircraft and related methods. Military aircraft shape the stamina for both nationwide defense and protrusion of power. The air transportations are significant to air dominance, strike, early warning, airlift, scouting, sea control, ground attack and command and control. Development in air transportation price and ability therefore present important controlling probability for decreasing defense expenses.

  • The B-52H BUFF aka Big Ugly Fat Fellow
    A sum of seven hundred and forty four B-52s were created with the final, a B-52H, transported in 1962. The H representation is the only one that is still in the Air Force account and are all allocated to Air Combat Command. The very first of 102 B-52H’s was transported to the Strategic Air Command in 1961. The H representation can hold up to twenty air instigated cruise missiles. Plus, it can hold the usual cruise missile that was instigated from the B-52G representations.
  • The F-117A Nighthawk Attack Fighter
  • The very first F-117A was transported in the year 1982, and the final Nighthawk deliverance was in the summer of year 1990. The F-117A manufacture verdict was ready in 1978 with a diploma presented to Lockheed Advanced Development Projects.
  • Contact Kinetic Die Casting Company to get a price for aluminum die casting parts or die casting tooling, call toll free 800-524-8083 and ask for sales. Or email us at sales@kineticdc.com for a fast response on a price quote.

    Kinetic Die Casting manufactures aluminum die castings creating aluminum die casting boxes, aluminum handle hardware, and aerospace die casting. If you would like to get a quote, please visit our website: Kinetic Die Casting Company

    Posted in Aircraft Parts | Tagged , , , , , , , , , | 3 Comments